GALEA SPA MASSAGE MANUAL

PEDICURE SPA USER MANUAL
®
GALEA
Before Operating the unit, please read this manual thoroughly and retain it for future reference .
LEASE TAKE NOTE! Thoroughly inspect each shipment immediately upon arrival. It is
important that you notify the driver and insist on a notation of the damage. Make this
notation directly on the freight company’s waybill or bill of lading. Failure to note damage on
the waybill or bill of lading may impede and/or prevent any claims that you may have
against the freight carrier.
If missing parts or damage is found. Please notify the carrier at once and request an
inspection. DO NOT DISCARD THE SHIPPING BOX. If you give the carrier a clear receipt
for goods that have been damaged in transit, you do so at your own risk and expense.
TRADEMARK DISCLAIMER
GALEA is the registered trademarks of ProSpaDepot. Reproduction or reuse of part or all of trademarks are
expressly prohibited without written permission from ProSpaDepot. Due to limitation of the printing process, product colors shown might look
different from actual colors. ProSpaDepot will not be responsible for any misprint of this advertisement. ProSpaDepot’s footspa specification
and pricesmay change without prior notice. Pedicure Spas are intended for professional used only, always follow your State Board’s sanitation
anddisinfectant guideline.

Table of Contents
SAFETY PRECAUTIONS: ...
. 3
Parts
Identifying Parts for GALEA® Model ...
. 4
SPA to SPA RECOMMENDED CLEARANCE: ...
... 5
Wall Clearance: ...
.. 5
MANICURE TRAY/ ARMREST / BACK REST INSTALLATION ...
. 6
Up/Down Swinging Armrest ...
...6
Plumbing Connections ...
.. 7
Power Drain (optional) ...
..7
Gravity Drain (No Drain Pump) ...
.8
Plumbing Flow Pattern for Power Drain...
...8
Plumbing Flow Pattern for Gravity Drain ...
.9
HOT AND COLD WATER SUPPLY LINES ...
...9
ELECTRICAL AND PEDICURE SPA COMPONENT SPECIFICATIONS ...
...1 1
OPERATION AND CARE INSTRUCTIONS ...
..1 2
MAGNETIC JET COVER REMOVAL & INSTALLATION ...
. 13
JET HOUSING REMOVAL & INSTALLATION ...
.. 14
MASSAGE SYSTEM & REMOTE CONTROLLER ...
... 15
MASSAGE TOP CHAIR INSTALLATION ...
... 16
CLEANING REQUIREMENT FOR PEDICURE SPAS ...
.. 17
2

___________________________________________________ Safety Precautions
READ AND FOLLOW INSTRUCTIONS CAREFULLY
Warning
SAFETY PRECAUTIONS:
THIS PRODUCT IS FOR INDOOR USE ONLY
DISCONNECT POWER SUPPLY CORD BEFORE SERVICING
This product is to be connected to a branch circuit outlet protected by a Class A GROUND FAULT CIRCUIT
INTERRUPTER (GFCI), and the GFCI shall be tested regularly for continued protection and correct operation. If a
Class A GFCI protected outlet is not available, DO NOT USE THIS PRODUCT! Please contact a licensed
electrician for installation of a Class A GFCI according to local electric codes, or equivalent.
Warning
DO NOT USE if you are diabetic, have poor circulation, or if any area of your feet or legs
is inflamed or has an open sore. Consult your physician before using if you have any kind of
fungal infection, swelling, fracture or persistent pain.
Warning
TO REDUCE RISK OF INJURY, DO NOT PERMIT CHILDREN TO USE
THIS UNIT UNLESS THEY ARE CLOSELY SUPPERVISED AT ALL TIME
Warning
LIRE LES INSTRUCTION DU FABRICANT AVANT DE METTRE EN MARCHE
UTILISER SEULEMENT A L’INTERIEUR
COUPER LE COURANT AVANT DE PROCEDRE AU DEPANNAGE, AU NETTOYAGE
1. Excessive water temperature is dangerous and should be checked BEFORE use.
2. Maximum temperature of the water should never exceed 100 degrees F.
3. DO NOT STEP/ STAND IN FOOT BASIN.
4. Always enter and exit the Pedicure Spa slowly and carefully.
5. NEVER bring and / or operate any electrical devices into or near the Pedicure Spa.
6. Maximum load in spa chair is 250lbs (114kg).
7. Do not over use of bleach or it will damage the spa , 1 teaspoon of 5.25% bleach for each gallon of water is recommended.
STATES’ NOTICE
In the common wealth of most of the States, all pedicure spas shall be installed for Commercial usage in the
states, are required to have backflow preventer. This equipment shall be installed between the water inlets and
the spa at Salon’s cost.
PLEASE SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
3

________________________________________________ Identifying Part____ Parts
Identifying Parts for GALEA® Model
(Pedicure Whirlpool with Massage System)
14
1
15
12
2
3
13
4
11
9
5
10
6
7
8
10. Drain Stopper
1. Chair Cushion with
5. Footrest
11. Ecojet ™ Jet
Massage
6. Jet On/Off Knob
12. Flex Water Filler/Spray
2. Armrest Cushion
7. Hot/Cold Water Mixer
spout
3. Manicure-Tray (Optional)
Valve
13. Massage Remote Control
4. Angelic Bowl
8. Sani-Drain™ System with
14. Back Flow Preventer
Discharge On/Off Knob
(Optional)
9. Up/Down Armrest
15. Liner Hook
4

_______________________________________________________ Installation
SPA to SPA RECOMMENDED CLEARANCE:
Wall Clearance:
5

_____________________________________________________ Installation
MANICURE TRAY/ ARMREST / BACK REST INSTALLATION
Up/Down Swinging Armrest, Manicure tray up and down
Press locking latch
Maincure Tray
To fold down tray
Armrest
Back Rest:
1. To set backrest up: Lift up the backrest until a “Click” is heard. Make sure the lever is locked
before operating.
2. To fold down backrest: Lift up lever handle located on the left side / bottom of Chair.
6

_______________________________________________________Installation
Plumbing Connections:
Warning Before any connection, pay attention to these subjects:
1. Debris or residue may become lodged into the Hot and Cold hoses during construction, which may clog
the Hot and Cold Mixer. To clean, drain a good amount of water from water hoses to bucket before
connecting them to the pedicure spa. Failure to do so may void your Warranty.
2. Hooking up a used Hot/Cold flex hose is not recommended since debris from broken rubber seal might
clog water mixer. Failure to do so may void your Warranty.
3. Backflow preventer: Due to differences in construction lay-out of your Salon and City’s plumbing code,
please contact your local Plumber to fulfill your needs as required. Backflow Preventers are not supplied
by the pedicure spa manufacturer.
4. Check valve is an optional part and supplied free of charge for your convenience. Factory is not liable for
this Check valve.
5. Maximum Inlet water pressure must be under 75 PS I .
Power Drain (optional):
Seat Back
Back Shell Mounting Screws
Up/Down Swinging Arm Rest
3/4” PVC Drain
1/2” ID Cold Water
1/2” ID Hot Water
9.5”
3/4” Check Valve
5.5”
25"
7

_______________________________________________________ Installation
Gravity Drain (No Drain Pump):
1/2 “ ID Cold Water
1/2 “ ID Hot Water
1 1/2 “ pipe
2,5”
1 1/4 “ pipe
5,5”
25”
Plumbing - Flow Pattern - Power Drain
Hot/Cold water Inlet & Back-Flow Preventer (Not Included)
Optional as required by Local city Plumbing Code
1/2”
Drain Pump
1/2”
Check Valve
(included)
8

_____________________________________________________________ Installation
Plumbing Flow Pattern for Gravity Drain:
Hot/Cold water Inlet-Back-Flow Preventer (Not Included)
Optional as required by Local city Plumbing Code
1 1/2”
1 1/4” Flex Hose Removable Connection
HOT AND COLD WATER SUPPLY LINES
Carefully connect ½” ID supply hoses (not provided) to fresh water sources. Shut-off valves (not
provided) should be utilized. Valves should be placed outside the tub for easy access.
Before water line connections, please follow below:
Determine if your spa chair is used for a new construction of a salon or a replacement spa chair.
1 . New construction : Make sure to remove any and all debris and/or dust from current hot cold
water pipes before hooking up to spa. Suggested direction to remove debris: turn on water and
drain into a bucket or container. See illustration below:
2. Replacement Spa : Always use new hot/cold water hoses when connecting a new spa chair to
prevent debris, such as old rubber particles, from clogging the system
9

______________________________________________________________________ Installation
CONNECT DRAIN WITH POWER DRAIN (PUMP) OR GRAVITY DRAIN (NO PUMP)
Using ¾” schedule 40 PVC (Power Drain) or 1 ¼” flex tube (Gravity Drain) and appropriate traps.
Connect drain to meet local plumbing codes.
Rubber connection to the drain should be removable for easy service and should not be permanent to
prevent damages.
10

________________________________________________ Specifications
ELECTRICAL AND PEDICURE SPA COMPONENT
SPECIFICATIONS
All electrical connections MUST be made by a qualified, licensed electrician in accordance with Local & National
Electrical and Building Codes. A 110V-50/60 Hz, 15 Amp, GFCI protected grounded circuit MUST be used to
supply power to the Pedicure Spa. A dedicated circuit must be used with a GFCI. All wiring must conform to
National & Local Electrical Codes .
WARNING: IT IS EXTREMELY IMPORTANT THAT THE FOOT SPA OPERATES WITH GFCI PROTECTION
VERY IMPORTANT Both back of chair and seat are adjustable. When both are at maximum positions one must
allow 18”(44cm) from back wall to foot spa. This minimum distance assures unobstructed recline. Failure to follow
this required dimension might damage your spa components and plumbing connections, which will void your
warranty.
PEDICURE SPA SPECIFICATIONS:
Construction: Marble composite, high gloss, acetone-proof gel coat.
Two (2) electro-mechanical knobs control the drain and whirlpool.
Electro-mechanically operated reclining, massaging, and sliding seat with hand held control.
One (1) pipe-less whirlpool jet. (Pipe-free technology)
Power drain (optional) or Gravity drain (no drain pump)
Extendable water spray positioned well above water line, air gap is accommodated with back-flow
prevention required by plumbing code
Armrest swing up / down.
SPECIFICATIONS
Spa Dimensions &
GALEA = 30” (W) x 54” (L)
Weights
All Models fully reclined: 74” (L). With Manicure Tray Installed: 46” (W)
Empty Weight: ~ 200 lbs. Shipping Weight: ~ 260 lbs.
Adjustable Stool Height
Pedicure Stool: 12” - 13”.
Spa Water Capacity
~ 4-5 US Gallon
Jet Motor
120 VAC. at 85W 60Hz
Massage Motors,
24VDC, 2.5A x 5
Seat Sliding & Reclining
Discharge Pump
Motor - 120V at 85W 60 Hz
Maximum vertical lift: 3ft . Flow rate 500 GPH @ floor level
Power source
115 VAC, 60HZ. Power needed per spa chair = 6 Amp
Electrical Switches
One (1) electro-mechanical knob for the Whirlpool. Rated at 5A contact.
One (1) electro-mechanical knob for the Drain. Rated at 5A contact.
Plug & Play Installation
Installation should be made with connection at the external interface parts.
Please consult with your local plumber.
Safety
GALEA® Pedicure Spa is UL listed.
11

____________________________________________________ Operation & Care
tion and Care
OPERATION AND CARE INSTRUCTIONS
Filling Water
1. Turn Counterclockwise to remove. Turn Clockwise to install.
Close the Drain Stopper by turning the Drain Knob counterclockwise. Utilizing the single lever hot/cold
mixer faucet located on the front of the Pedicure Spa, fill the tub to the water level above the whirlpool
jet at least 1 inch. You must completely submerge the jet. If during the operation of the whirlpool, the
water level decreases, simply add more water.
Whirlpool Starting
Turn the Jet Knob located on the right side of the front panel to clockwise to turn on.
Turn counterclockwise to shut off.
Warning : Do NOT turn “ON” the JET PUMP KNOB unless adequate water is in the tub.
THE WARRANTY IS VOID IF THE PUMP HAS BEEN RUNNING DRY
Draining
Turn the Drain Knob clockwise to open the Drain Stopper. Power Drain will turn on automatically if drain pump exist.
D
Dual Action Electro-mechanical Switch located on the left side of the front panel) When activating the switch,
it will raise the drain-stopper and power up the drain pump (if exist) at the same time.
Warning Do NOT turn “ON” the DRAIN PUMP KNOB unless adequate water is in the tub.
THE WARRANTY IS VOID IF THE PUMP HAS BEEN RUNNING DRY
NOTE :
Whirlpool action can cause even small amounts of soap or body oil to foam excessively. For this reason, refrain from
using these products during the whirlpool cycle .
Water Control Knob Cold/Hot
Jet Knob
Drain Knob
12

MAFNETTIC JET COVER REMOVAL & INSTALLATION
1. Turn counterclockwise to remove. Turn clockwise to install
13

______________________________________________ Operation and Care
JET HOUSING REMOVAL & INSTALLATION
1. Turn clockwise to remove motor. Turn counterclockwise to install motor.
14

______________________________________________ Operation and Care
MASSAGE SYSTEM & REMOTE CONTROLLER:
1. Press Auto Button to start Auto mode. Press again to turn off massage.
Auto and Manual mode will run for duration of 15min.
2. Press any button (Rolling/Spot, Kneading, Tapping, Combine) to enter Manual mode.
3. Press Rolling/Spot to stop rolling up/down and stop at desired spot.
4. Press Intensity button to select tapping intensity.
5. Vibro Button/LED is an option. Pressing this button will resume with Tapping action.
6. Press any chair button (Recline, Incline, Backward, Forward) to move the chair to desired positions.
15

_______________________________________________ Operationand Care
NOTE : If the Massage Chair is not provided, then the end-user will need to install a UL listed and cUL/CSA
certified massage chair with a suitable Class 2 Power Supply.
TOP MASSAGE CHAIR BASIC INSTALLATION INSTRUCTIONS:
Fig.2
Fig.1
Install seat cushion with 2 screw-Knobs
Drill 4 mounting holes ½”.Width=16.5”
Lever the back massage and secure 2 hinge
Length=11 .Install seat frame and secure 4
screws onto the metal brackets.(Do not turn
screws from bottom base. Using the provided
the screws all the way in )
stand-off blocks to adjust the height of seat frame as
Leave 1/4” thread screw head for sliding
needed to allow seat frame to travel freely.
Install back shell with 4 screws as Fig.3
Controller PCB
Lift up back massage to engage
locking device. (Manually adjust
actuator rod to lock as needed)
Install back cushions.
Plug AC cord to power strip
Located inside of the tub base.
Fig.3
16

WARNING
Y ou must always refer to your state or local guidelines for cleaning requirements .
Overnight soaking with overdosed Chlorine may damage rubber part in basin
CLEANING PROCEDURE IS REQUIRED BY STATE BOARDS
Note: *** A cleaning log should be kept with each pedicure spa ***
Each State will have slight differences in cleaning policies, please check with your state’s Bureau of Barbering
and Cosmetology or Regulatory Authority for specific details.
Safety Requirements for Pedicure Spas
The Bureau of Barbering and Cosmetology requires that salons using whirlpool pedicure foot spas must
follow these disinfecting procedures to ensure proper cleaning and maintenance of the equipment and to
prevent the spread of bacterial or parasitic disease.
Violation of this section may result on an administrative fine and/or disciplinary action. Each foot spa that
is not in compliance with this section may result in a separate violation.
NOTE: Authority cited: Section 7312, Business and Profession Code. Reference: Section 7312 (e),
Business and Profession Code.
Below is a suggestion for your pedicure spa chair’s cleaning procedure:
After Each Customer
1. All water shall be drained and all debris shall be removed from the spa basin.
2. The spa basin must be cleaned with soap or detergent and water
3. The spa basin must be disinfected with an EPA-registered disinfectant with demonstrated bactericidal,
fungicidal, and virucidal activity, which must be used according to manufacturer’s instructions.
4 . The spa basin must be wiped dry with a clean towel.
At the End of Each Day
1. The screen shall be removed, all debris trapped behind the screen shall be removed, and the screen and the
inlet shall be washed with soap or detergent and water.
2. Before replacing the screen, the screen shall be totally immersed in an EPA-registered disinfected with
demonstrated bactericidal, fungicidal and virucidal activity, which must be used according to the
manufacturer’s instructions.
3 . The spa system shall be flushed with low sudding soap and warm for at least 10 minutes, after which the spa
shall be rinsed and drained.
At Least Once A Week
1. The spa basin shall be filled completely with warm water and 1 teaspoon of 5.25% bleach for each gallon of
water, or a solution of Sodium Hypochlorite of approximately 50ppm used according to manufacturer’s
instructions.
2. The spa system shall be flushed with the bleach and water solution, or Sodium Hypochlorite solution, for 5-10
minutes and allowed to sit for 6-10 hours.
3 . The spa system shall be drained and flushed with water before use upon a patron.
17

WARNING
PROPER INSTALLATION ACCORDING TO THIS MANUAL IS REQUIRED.
FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY AND/OR WARRANTY WILL BE NULL.
YOU MUST HAVE A QUALIFIED LICENSED PLUMBER TO CONNECT THE SPA IN PLACE SAFELY
UL SAFETY RECOGNIZED FOR UNITED STATES AND CANADA.
ProSpaDepot Inc, 7171 Fenwick Lane, Westminster, CA 92683,USA
Customer Service : TEL 888-213-7728FAX: 714-908-7694
www.prospadepot.com
©2014 All Rights reserved. Design and Specifications are subject to change without notice
18

PROSPADEPOT INC, LIMITED FACTORY WARRANTY
LIMITED COVERAGE:
All parts are solely repaired or replaced, at ProSpaDepot’s option, any evaluated defects in workmanship, except the strictly excluded conditions below. Labor,
shipping and return shipping are not included. ProSpaDepot reserves the rights to send out new or equivalent to new as replacements.
ProSpaDepot shall have no obligation to repair, replace, or refund until the verification process byProSpaDepot is completed.
ProSpaDepot's limited warranty applies only to ProSpaDepot Pedicure Spas utilized in the United States.
This limited warranty is not transferrable. Furthermore, this limited warranty is void if removed from its place of initial shipment.
*Spa Tub: Shipping or return shipping cost of spa tub is not included in the limited warranty.
*Pedicure Stool, Manicure Stool : 1-Yr warranty
on adjustable hydraulic and wheels from the date of shipment. No warranty
on Upholstery and any other parts not
listed.
WHAT IS NOT COVERED:
Mishandling, damages from shipping, expenses from returning eligible defectives to factory, improper installation, abuse, misuse, neglect, accidental events,
freight damages, damage resulting from a person standing in the Pedicure Spa’s basin or other similar stress to that basin, normal wear and tear on upholstery, or
natural disaster.
REQUEST FOR SERVICE:
Prior to calling, please have your Salon or company name, address, telephone number, contact name, model name, and serial number, and a brief description of
the problem. Contact ProSpaDepot's Customer Service Department to report defects or if you have questions on warranty prior to the expiration date of warranty
at:
ProSpaDepot Inc. Customer Service Department
7171 Fenwick Lane, Westminster, CA 92683,
USA
Customer Service : 888-213-7728 FAX: 714-908-7694
www.prospadepot.com
LENGTH OF WARRANTY:
*Twelve (12) months starting from the date of shipment. Purchase invoice, bill of sale, date of purchase, or delivery receipt are required by ProSpaDepot to qualify
for your warranty coverage.
UNAUTHORIZED REPAIR:
Any performed or attempted repair or modification on the spa without explicit authorization in writing from ProSpaDepot will void this limited warranty .
DISTRIBUTOR WARRANTIES:
There is no distributor, dealer, general contractor, or other party has any legal rights to apprentice ProSpaDepot to any obligations or charges to this warranty in
any extent.
LIMITED DAMAGES:
Allowed by law, ProSpaDepot will fully extend its options to disclaim and refuse any liability for substantial damages including, but not limited to, loss of business
reputation, decrease in profits, or any fastidious damages other than these limited damages. In some states, the mentioned damages are not allowed to lawfully
sustain; therefore, they may not apply to you.
*Warranty - Parts Sale:
All parts purchased from ProSpaDepotCustomer Service will have a 90-Day warranty from shipped date, except Complete Chair Top with Massage System and
Complete Spa Base with Plumbing. ProSpaDepotreserves the rights to send out new or equivalent to new as replacements. All part sales are final and no refunds
will be accepted.
*Complete Chair Top with Massage System will have a 6-Month Limited Warranty from the date of shipment.
*Complete Spa Base with Plumbing Installed will have a 6-Month Limited Warranty from the date of shipment.
*Continuing a policy of constant research and development to improve the quality of our products, ProSpaDepot, Inc. reserves the right to change pricing,
parts, design and specifications without prior notice or obligation.
Your Initials: